Density of Sprite
Essay Preview: Density of Sprite
Report this essay
Hamza Aziz
General Chemistry I Lab
09/12/2007
Lab 7
Density of Sprite and Diet Sprite
Abstract:
The density of regular Sprite was found to be 1.037 +/- g/mL. compared to Diet Sprite which was 0.9965 +/- g/mL. Among the three volumetric glassware Pipette was most precise (у=0.0016 g/mL). Burette was the second best (у=0.0023 g/mL) and graduated cylinder was the least precise (у= 0.007 g/mL). Density was found to be intensive property. The slope of the graph of mass against volume was 1.05 g/mL, with the best linear fit for the data.
Introduction:
In chemistry, accuracy and precision are very important. Accuracy is the degree of conformity of a literature value and precision is a degree to which further calculated values show similar result. In this lab, the volume of the solution (diet or regular) is measured using the Pipette, Burette, and Graduated Cylinder respectively. The mass of the solution is then measured to calculate the density of the soda. Density is mass of a substance per unit volume2. How heavy the substance is according to its size or volume. The volume of liquid is measured in mL and mass in grams. Since, the density of water is 1g/cm3 ; therefore Diet Sprites density should be equal to or a little bit more then water. The hypothesis was that regular Sprite will have higher density because it has a higher sugar concentration present which increases the mass per volume ratio of the solution. In this experiment only regular Sprite was used. The results are then compared to another group which calculated the density of Diet Sprite.
Experimental:
Part A
In the first phase of the experiment, the 25 ml Pipette is used to measure the volume and mass of the solution. Another beaker was in grams. Pipette was used to measure 25ml of regular Sprite. The solution was drawn the beaker and its mass was measured on the electronic balance. Mass of the solution was then calculated by subtracting beakers weight and beaker with solutions weight. When 25ml solutions mass was known, its density was calculated by dividing mass by its volume. The steps were repeated once again to get the precision of the glassware.
In the next step, Burette was used to measure 25ml solution. The mass of empty beaker was measured. Burette was used to measure 25ml of solution and then it was drawn into the beaker. After that the mass of the beaker with solution in it was measured. Beakers mass and beaker with solutions mass were subtracted to get the solutions mass. The density of the solution was calculated by dividing the mass by volume. This part was performed once more to get the average density of the two trials.
In the last step of the first part, a graduated cylinder was used to find the density of the solution. An empty Graduated Cylinders mass was measured on the weighing balance. Then, the cylinder was filled with solution up to 25ml mark. Mass of the solution was calculated by subtracting the mass of the cylinder and cylinder with solution in it. The density was calculated by dividing mass by 25ml volume.
Same methods were used to perform this experiment one more time. The measurements and densities from this experiment can be found in Table 1. Figure 1 shows the graph and data collected from all three of the labs on Tuesday, Wednesday, and Thursday.
Part B
This time only burette was used to calculate the density of five different volumes: 5ml, 10ml, 15ml, 20ml, and 25ml because it was found to be the easiest and quickest glassware among the three to use. The weight of an empty beaker was measured which was 50.540 g. 5ml of Sprite was carefully measured in burette and was drawn into the beaker. Beakers weight with solution in it was measured. After that another 5ml solution was added and weight was measured on electronic balance. The process was repeated by adding 5ml to the solution until the volume reached 25ml. Mass of the beaker with solution was subtract to the mass of beaker every time 5ml were added to the solution to get the mass of the solution by itself. Densities were calculated and graph was plotted of the whole experiment. Table 2 shows the results of the experiments. Figure 2 shows the densities measured in this experiment.
Results and Discussion
Table 1
The standard deviation of the densities calculated from three different volumetric glassware can be calculated through following equation1:
Where N stands for number of trials and x is the density.
Table 1
Pipette
Burette
Graduated Cylinder
Trial 1
Trial 2
Trial 1
Trial 2
Trial 1
Trial 2
Mass of container
50.781 g
50.461 g
59.707 g
59.701 g
88.883 g
88.884 g
Beaker w/ soda mass
76.630 g
76.410 g
84.435 g
85.601 g
114.26 g
114.35 g
Mass of soda
25.849 g
25.949 g
24.728 g
25.900 g
25.383 g
25.473 g
Volume of soda
24.99 ml
25.01 ml
24.85 ml
24.9 ml
24.9 ml
25 ml
Density
1.034g/ml
1.037g/ml
0.9951g/ml
1.040g/ml
1.02g/ml
1.01g/ml
Mean Density (g/ml)
1.035
1.018
Standard Deviation
0.0016
0.0023
0.007
Figure 1: Shows the density of Sprite and Diet Sprite calculated through three volumetric glassware.
Table 1 shows the results from Part A of the experiment.
According to these calculations pipette turned out to be the most precise since it has the least standard deviation of 0.0016. Figure 1 shows the pooled data of Sprite and Diet Sprite from both groups. It illustrates that pipette is the most precise because the density values are the closest to each other than any other glassware.
The results showed that regular Sprite was denser than Diet Sprite because of the sugar molecules present in the solution made it heavier. As Figure 1 illustrates, that the Diet Sprites density is around 1g/ml which is the density of water.